收藏本站
LTM4619
PIN FUNCTIONS
1– OUT ? V OUT
FREQ ? V IN ?
I RIPPLE =
PACKAGEROWANDCOLUMNLABELINGMAYVARY
AMONG μModule PRODUCTS. REVIEW EACH PACKAGE
LAYOUT CAREFULLY.
V IN (J1 to J3, J10 to J12, K1 to K4, K9 to K12, L1 to L5,
L8 to L12, M1 to M12): Power Input Pins. Apply input
voltage between these pins and PGND pins. Recommend
placing input decoupling capacitance directly between V IN
pins and PGND pins. For V IN < 5.5, tie V IN and INTV CC
together.
V OUT1 , V OUT2 (A10 to D10, A11 to D11, A12 to D12, A1 to
D1, A2 to D2, A3 to D3): Power Output Pins. Apply output
load between these pins and PGND pins. Recommend
placing output decoupling capacitance directly between
these pins and PGND pins.
PGND (H1, H2, H4, H9, H11, H12, G1 to G12, F1 to F5,
F7 to F12, E1 to E12, D4 to D9, C4 to C9, B4 to B9, A4 to
A9): Power ground pins for both input and output returns.
INTV CC (F6): Internal 5V Regulator Output. This pin is for
additional decoupling of the 5V internal regulator.
EXTV CC (J4): External Power Input to Controller. When
EXTV CC is higher than 4.7V, the internal 5V regulator is
disabled and external power supplies current to reduce
the power dissipation in the module. This will improve the
efficiency more at high input voltages.
SGND (J6, J7, H6, H7): Signal Ground Pin. Return ground
path for all analog and low power circuitry. Tie a single
connection to PGND in the application.
MODE/PLLIN (H8): Mode selection or external synchroniza-
tion pin. Tying this pin high enables pulse-skipping mode.
Tying this pin low enables force continuous operation.
Floating this pin enables Burst Mode operation. A clock
on the pin will force the controller into the continuous
mode of operation and synchronize the internal oscillator.
The suitable synchronizable frequency range is 250kHz to
780kHz subject to inductor ripple current limits described
in the FREQ/PLLFLTR pin section. The external clock input
high threshold is 1.6V, while the input low threshold is 1V.
FREQ/PLLFLTR (J8): Frequency Selection Pin. An internal
lowpass filter is tied to this pin. The frequency can be
selected from 250kHz to 780kHz by varying the DC volt-
age on this pin from 0V to 2.4V. The nominal frequency
setting is 500kHz. Frequency selection can be modified as
long as the inductor ripple current is less ≈40% to 50%
at the output current
1 ? V ?
L
Where FREQ is selected operating frequency and L is
the inductor value. Leave this pin floating when external
synchronization is used.
TK/SS1, TK/SS2 (K8, K5): Output Voltage Tracking and
Soft-Start Pins. Internal soft-start currents of 1.3μA charge
the soft-start capacitors. See the Applications Information
section to use the tracking function.
V FB1 , V FB2 (K7, K6): The negative input of the error
amplifier. Internally, this pin is connected to V OUT with
a 60.4k precision resistor. Different output voltages can
be programmed with an additional resistor between V FB
and SGND pins. See the Applications Information section
for details.
COMP1, COMP2 (L7, L6 ): Current Control Threshold and
Error Amplifier Compensation Point. The module has been
internally compensated for most I/O ranges.
PGOOD (H5): Output Voltage Power Good Indicator. Open
drain logic output that is pulled to ground when the output
voltage is not within ±7.5% of the regulation point.
RUN1, RUN2 (J9, J5): Run Control Pins. 0.5μA pull-up
currents on these pins turn on the module if these pins
are floating. Forcing either of these pins below 1.2V will
shut down the corresponding outputs. An additional 4.5μA
pull-up current is added to this pin, once the RUN pin rises
above 1.2V. Also, active control or pull-up resistors can
be used to enable the RUN pin. The maximum voltage is
6V on these pins.
SW1, SW2 (H10, H3): Switching Test Pins. These pins
are provided externally to check the operation frequency.
4619fb
6
For more information www.linear.com/LTM4619
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
LTM4627MPY#PBF IC DC/DC UMODULE 15A 133-BGA
LTM4628EV#PBF IC DC/DC UMODULE 16A 144-LGA
LTM8008HV#PBF IC DC/DC UMODULE 16-LGA
LTM8020IV#PBF IC DC/DC UMODULE 200MA 21-LGA
LTM8023MPV#PBF IC BUCK SYNC ADJ 2A 50LGA
LTM8025MPV#PBF IC CONVERTER BUCK 3A ADJ 70LGA
LTM8026MPV#PBF IC UMODULE 36VIN 5A CVCC 81LGA
LTM8027EV#PBF IC BUCK SYNC ADJ 4A 113LGA
相关代理商/技术参数
LTM4619IVPBF 制造商:Linear Technology 功能描述:Dual 26V 4A DC/DC uModule Reg. LGA144
LTM4620 制造商:LINER 制造商全称:Linear Technology 功能描述:38V, 10A DC/DC ??Module Regulator with Advanced Input and Load Protection
LTM4620A 制造商:LINEAR_DIMENSIONS 制造商全称:LINEAR_DIMENSIONS 功能描述:Dual 8A per Channel Low VIN DC/DC ??Module Regulator
LTM4620AEV#PBF 制造商:Linear Technology 功能描述:DC/DC CONVERT DUAL 0.6-5.3V 13A 制造商:Linear Technology 功能描述:DP-uModule, 26A Single or 13A Dual DC/DC uModule Regulator (Higher Vout version
LTM4620AEY#PBF 制造商:Linear Technology 功能描述:DC/DC CNVRTR 2X0.6-5.3V 144BGA 制造商:Linear Technology 功能描述:DC-DC CONV, BUCK, ADJ, 780KHZ, BGA-144, Primary Input Voltage:16V, No. of Output 制造商:Linear Technology 功能描述:DC-DC CONV, BUCK, ADJ, 780KHZ, BGA-144, Primary Input Voltage:16V, No. of Outputs:2, Output Current:13A, No. of Pins:144, Operating Temperature Min:-40C, Operating Temperature Max:125C, Package / Case:144-BGA , RoHS Compliant: Yes
LTM4620AIV#PBF 制造商:Linear Technology 功能描述:DC/DC CONVERT DUAL 0.6-5.3V 13A 制造商:Linear Technology 功能描述:DP-uModule, 26A Single or 13A Dual DC/DC uModule Regulator (Higher Vout version
LTM4620AIY#PBF 制造商:Linear Technology 功能描述:DC/DC CNVRTR 2X0.6-5.3V 144BGA 制造商:Linear Technology 功能描述:DC-DC CONV, BUCK, ADJ, 780KHZ, BGA-144, Primary Input Voltage:16V, No. of Outputs:2, Output Current:13A, No. of Pins:144, Operating Temperature Min:-40C, Operating Temperature Max:125C, Package / Case:144-BGA , RoHS Compliant: Yes
LTM4620EV#2FMPBF 制造商:Linear Technology 功能描述: